SIPANEL Engineering

Engineering Insights

Technical articles focused on problem context, engineering cause, SIPANEL execution logic, pending proof states, and internal project resources.

Engineering Article Library

Search by topic or filter by engineering category.

11 articles
Daylighting and Transparent Roofing

Falls through rooflights on industrial roofs in winter work

On most industrial roofs, rooflight sheets are made to let light in, not to carry a person, and in winter they vanish under snow, dust or paint beside similar metal sheets. The fall risk must be controlled in design and installation: layout away from access routes, permanent mesh or guarding, a defined walkway and a safe access plan, not momentary caution while clearing snow.

Structure
Problem to CTA
Proof state
Pending verified asset
Read engineering insight
Aluminium Cladding

Rain penetration behind aluminium cladding: where water gets in

An aluminium cladding panel is essentially a rain-deflecting skin, not the last waterproofing layer. In wind-driven rain some water passes joints and edges. If the cavity has no drainage path, the backing wall has no water-resistive layer, or the flashings at openings and parapets are not resolved, that water reaches the interior. The durable fix is correcting the water path, not adding more silicone.

Structure
Problem to CTA
Proof state
Pending verified asset
Read engineering insight
ETFE Systems

ETFE Cushions and Hail: Punctures, Pressure Loss and Repair

ETFE foil is highly elastic, and a cushion at design pressure absorbs most hail impact by elastic deformation. The main risk lies elsewhere: a cushion gone soft from a blocked filter, a faulty fan or a power cut, small holes invisible from below, and hail held in low spots. After heavy hail, check air-unit alarms, cushion shape and drainage from safe access, and repair any hole before it grows.

Structure
Problem to CTA
Proof state
Pending verified asset
Read engineering insight
Standing Seam and ZIP Roofing

Standing Seam Roof Wind Uplift: Why Panels Peel From the Edge

Strong wind creates suction on a roof that is much higher along edges, at corners, around the ridge and on overhangs than mid-roof. A standing seam panel is held only by concealed clips engaged in its seam, so wind resistance belongs to the whole assembly of panel, seam, clip, fastener and purlin, not to sheet thickness. Detachment usually starts at an edge or trim and, if not restrained, spreads.

Structure
Problem to CTA
Proof state
Pending verified asset
Read engineering insight
Sandwich Panel Systems

Sandwich Panel Building Heat Loss: Where the Heat Escapes

In a sandwich panel building, the middle of the panel is usually the strongest part of the envelope. The weak points are panel joints, roof-wall junctions, openings, and places where metal crosses the insulation layer. Air leakage and thermal bridges should be measured before panels are replaced. The sound order: measure in cold weather, seal on the warm side, correct details, and only then decide on replacement.

Structure
Problem to CTA
Proof state
Pending verified asset
Read engineering insight
Retractable Roofs

Retractable Roofs in Snow and Frost: Winter Operating Logic

In winter a retractable roof has three states: closed, parked and moving, and snow and ice affect each one differently. The riskiest moment is usually the movement itself, when snow is lying on the skin or the tracks and seals have frozen. Before the cold arrives, it must be clear which state the system was checked in for snow, which conditions prohibit movement and who checks the roof before each operation.

Structure
Problem to CTA
Proof state
Pending verified asset
Read engineering insight
Tensile Membrane Structures

Ponding on Fabric Membrane Roofs: A Pre-Winter Check

Water and snow collect on a fabric roof wherever the membrane lacks enough curvature and slope, or where the drainage outlet is blocked. Ponding feeds itself: the weight of the water deepens the depression, which then draws in more water. Before winter, geometry, prestress, fittings and low points should be reviewed together; re-tensioning alone is not always the answer.

Structure
Problem to CTA
Proof state
Pending verified asset
Read engineering insight
Daylighting and Transparent Roofing

Rooflight Dripping in Autumn: Leak or Condensation?

If water drips from a rooflight only during or shortly after rain, and concentrates at laps, fixings or edges, it is usually a leak. If scattered droplets form on the inner surface on cold, dry nights and mornings, it is most likely condensation. The two need different fixes, and a wrong diagnosis makes the repair useless.

Structure
Problem to CTA
Proof state
Pending verified asset
Read engineering insight
Aluminium Cladding

Aluminium Cladding Joint Control for Industrial Facades

Facade quality depends on joint rhythm, fixing logic, edge conditions, and opening coordination being reviewed as an execution system, not only a finish choice.

Structure
Problem to CTA
Proof state
Pending verified asset
Read engineering insight
Sandwich Panel Systems

Why Sandwich Panel Joint Logic Controls Leakage Risk

Panel leakage risk is usually controlled by joint geometry, accessory coordination, and installation sequence before material ordering, not by panel selection alone.

Structure
Problem to CTA
Proof state
Pending verified asset
Read engineering insight
Standing Seam and ZIP Roofing

Standing Seam Roof Drainage Logic Before Execution

Roof performance depends on slope, drainage path, seam continuity, gutter capacity, penetrations, and edge transitions being resolved before installation begins.

Structure
Problem to CTA
Proof state
Pending verified asset
Read engineering insight