Engineering Insight

Falls through rooflights on industrial roofs in winter work

On most industrial roofs, rooflight sheets are made to let light in, not to carry a person, and in winter they vanish under snow, dust or paint beside similar metal sheets. The fall risk must be controlled in design and installation: layout away from access routes, permanent mesh or guarding, a defined walkway and a safe access plan, not momentary caution while clearing snow.

Winter brings the most roof traffic and the least visibility of rooflights

With every wave of snow and rain, people go onto the roofs of sheds, warehouses and halls more often: clearing snow to reduce roof load, freeing frozen gutters and outlets, finding a leak, tightening fixings after wind or checking rooftop equipment. This work is often done in a hurry, by maintenance staff or a small contractor, without an access plan. At the same time, rooflight strips are completely hidden under a layer of snow, and even without snow an old translucent sheet covered in dust or paint looks the same as the metal sheet of the same profile beside it. Someone who steps a little off line to reach a gutter may put their weight on a surface that was never made for a person without knowing it. Repeated news of falls from shed roofs shows this risk is not theoretical, but most of its causes can be controlled before winter and even before the rooflight is installed.

  • Rooflight strips cannot be seen under snow, and their boundary with the metal sheets cannot be found from the snow surface.
  • A translucent sheet with the same profile as the roof sheet, especially when dull or painted, is mistaken for metal even on a sunny day.
  • Rooflights often sit beside gutters, in valleys or near equipment, exactly where people must go to clear snow or make repairs.
  • Many existing sheds have no mesh under the rooflights, no guarding over them, no defined walkway and no anchor point.
  • Emergency winter repairs are usually done without a roof plan, so the person on the roof does not know where the rooflights are.

Why rooflight sheets cannot carry a person, and why the risk grows with time

A metal roof sheet works as a structural element between purlins and spreads a concentrated load to some extent, but a polycarbonate, GRP or glass rooflight sheet is chosen for light transmission, distributed wind and snow load and weathertightness. The weight of someone stepping, slipping or kneeling on it is a concentrated impact load, and the sheet's response depends on material type and thickness, support spacing, the number and type of fixings and the overlap detail. Even when a manufacturer claims an assembly is non-fragile, that claim only holds for that specific combination of sheet, fixings and purlin spacing, in new condition; fewer fixings, wider purlin spacing or a replacement sheet from another supplier can be enough to invalidate that claim. Over time, ultraviolet exposure, temperature cycling and air pollution make plastic sheets cloudy and brittle, and fine cracks at fixing holes reduce the remaining capacity. Finally, the risk lies in the layout more than in the material: when a rooflight is placed on the route people must take to reach a gutter or equipment, the fall risk has been designed into the building.

  • A translucent sheet is designed for distributed snow and wind load, not for the concentrated impact of a human body.
  • Non-fragility is a property of the whole installed assembly, not the sheet alone; changing fixings, purlin spacing or the overlap detail can invalidate it.
  • Non-fragile does not mean walkable; such a sheet is meant to stop a fall, not to serve as a walkway.
  • Sun ageing of plastic sheets and cracks around fixings reduce capacity without an obvious visible sign.
  • A rooflight beside a gutter, in a valley or in the way of equipment makes walking on or next to it practically unavoidable.
  • Local replacements with unknown sheets turn a uniform roof into a set of sheets with unknown behaviour.

Technical proof state

No metric, project result, or proof image is shown until a verified asset is attached.

Roof plan diagram with rooflights, walkway and guarding (pending verification)

The verified diagram should show a shed roof plan: rooflight strips in a distinct colour, gutters and valleys, a defined walkway from the access point to gutters and equipment, permanent mesh or grid under the rooflights, guarding along strips next to the walkway, and anchor points. A small section should also show the sheet, fixing and purlin combination. This technical asset is still pending verification.

  • Rooflight strip away from the gutter
  • Defined walkway
  • Permanent mesh under the rooflight
  • Guarding beside the walkway
  • Access point and anchorage

SIPANEL's logic for controlling falls through rooflights

01

Identify and map the rooflights

On an existing roof, every strip and individual rooflight is recorded on the roof plan: sheet type, visible condition, previous replacements, whether mesh or guarding exists, and distance from gutters and equipment. Before any snow clearing or winter repair, this plan must be in the hands of whoever goes onto the roof.

02

Lay out rooflights with access routes in mind

In new design, the rooflight layout is reviewed together with access routes to gutters, valleys and rooftop services. Strips are kept as far as practical from gutter edges and repair routes so that routine work does not require passing beside them.

03

Define the installed assembly as a system

Sheet type and thickness, purlin spacing, fixing type and number, and the overlap detail are recorded as one combination in the shop drawings. If the project specification requires non-fragility, evidence for that exact combination is requested from the supplier and checked during installation.

04

Permanent protection instead of momentary caution

Depending on use and how often the roof is accessed, permanent mesh or a metal grid under or over the rooflights, guarding along strips next to routes and a defined walkway on the roof are provided. These measures are coordinated with the rooflight's structure and sealing so they do not become a source of leaks or unwanted shading.

05

A safe access plan for snow and repairs

The operator is told which route and which fall-protection equipment to use for snow clearing and repairs, which tasks can be done from below or from the edge, and that nobody steps on a translucent sheet or an unidentified surface under snow. Roof work must follow occupational safety rules with a named person responsible for safety.

06

Handover, marking and periodic inspection

At handover, a roof plan showing rooflights, walkways and anchor points is given to the operator, and warning signs are fixed at roof access points. The condition of sheets, fixings and mesh is inspected before every winter, and any replacement uses the same approved combination.

Technical FAQ

View complete FAQ
Can you walk on a polycarbonate rooflight sheet?

No. A polycarbonate rooflight sheet, solid or multiwall, is chosen to transmit light and carry distributed snow and wind load, not the weight and impact of a person. Even if a sheet feels firm under hand pressure, it can break or pull off its fixings under the concentrated load of a step or a slip. A rooflight should never be part of a walkway.

Does a 'non-fragile' rooflight mean you can walk on it?

No. Non-fragile means the installed assembly stopped a person's fall in a defined test, not that it is designed for repeated walking or standing. The property also only applies to that combination of sheet, fixings and purlin spacing in new condition, and can be lost as the sheet ages or details change.

How can snow be cleared safely from a shed roof with rooflights?

Before going onto the roof, the rooflight positions are identified from the plan or from inside the hall and marked on the roof. Snow is cleared only from a defined walkway or with fall-protection equipment and guarding, and nobody steps on a surface that is hidden under snow. If no such route or equipment exists, the decision to clear snow should be taken with an engineering review and the person responsible for safety, not in a hurry.

Is a rooflight that has been in service for years and looks sound safe?

Looking sound is not enough. Plastic sheets gradually become cloudy and brittle in the sun, and fine cracks around fixings are not visible from a distance. Any rooflight whose installed assembly and condition are not documented should be treated as fragile until a competent person confirms otherwise.

What should be done on an existing shed where rooflights have no mesh or guarding?

In the short term, roof access is restricted and controlled, rooflight positions are marked on the plan and on the roof, and essential work is done only with temporary guarding or fall-protection equipment. As a permanent solution, mesh or a grid under or over the rooflights, a defined walkway and, where needed, replacing aged sheets with an approved combination are reviewed.

Review the rooflight risk on your roof before the next snow clearing

Send the roof plan or photos, the type and condition of the rooflight sheets and the routes used for snow clearing and repairs, and SIPANEL's technical team will review the rooflight layout, the need for mesh and guarding and the logic for safe access.