Engineering Insight
Rain penetration behind aluminium cladding: where water gets in
An aluminium cladding panel is essentially a rain-deflecting skin, not the last waterproofing layer. In wind-driven rain some water passes joints and edges. If the cavity has no drainage path, the backing wall has no water-resistive layer, or the flashings at openings and parapets are not resolved, that water reaches the interior. The durable fix is correcting the water path, not adding more silicone.
Problem
After the autumn downpours: damp patches by the windows, water at the base of the facade and silicone that leaks somewhere new every time
With successive autumn rain systems and rain driven against the walls by wind, many operators of office, retail, hospital and industrial buildings with aluminium cladding notice signs that were invisible in summer: damp patches on the inner wall below windows, blistered paint beside opening frames, water running out of the base of the facade or rust streaks on the pavement. The usual reaction is to have the contractor run more silicone around the panels. Sometimes the leak stops for a while, then reappears at another point in the next rain. The reason is that the problem is usually not in the panel face itself. An aluminium facade is a multi-layer system: the outer skin, the substructure and brackets, the air cavity, insulation and the backing wall, and the details at edges and openings. Water reaches the interior when the drainage path or the water-control layer is interrupted in one of these layers. Until that path is understood, every surface patch only moves the place where the leak shows up.
- Damp patches or blistered paint on the inner wall, especially below sills and beside opening frames, after rain driven by wind onto that elevation.
- Water running out of the base of the facade or above a canopy; in a ventilated cavity facade this can be normal drainage and is not a defect on its own.
- Wet, compressed or slumped insulation behind the panels, seen when a panel is removed, which has also reduced the wall's thermal performance.
- Rust streaks from brackets, screws or steel substructure parts, showing that water has stayed behind the panels for a long time.
- Leaks on the top floor that originate at the parapet coping or the top edge of the facade, not at the roof.
- Leaks that return after every round of sealant work, showing that water is travelling by a route other than the visible joint.
Engineering cause
The panel deflects rain; real waterproofing is decided in the cavity, the flashings and the backing wall
Rain crosses the outer skin by several mechanisms: the momentum of drops in wind-driven rain, gravity flow along surfaces that slope inward, surface tension that draws water under edges, capillary action in narrow joints, and the air-pressure difference between outside and the back of the panel. In a fully face-sealed approach, all of these forces are resisted by a single sealant line, and it only takes one break in its continuity for water to find a way in, for example from thermal movement, application without backer rod or poor adhesion to a contaminated surface. In a ventilated rainscreen approach, it is accepted that some water enters the cavity; that water must run down the face of the backing wall and be directed out at the base of the facade and above each opening. Most leaks come from places where this logic was left half-finished: block or insulation backing walls built without a water-resistive layer, the base of the cavity closed by mortar, debris or a profile, window frames not tied into the backing wall's water-control layer and sills without upstands and end dams, or a parapet coping without enough slope and overlap. Bracket anchor holes and services penetrations through the facade also create a direct path for water if they are not sealed at the backing wall. One diagnostic point matters too: not every interior stain is a leak; condensation on cold wall surfaces or frames on cold nights, when the indoor air is humid, can produce similar signs.
- Face sealant is the first line, not the only line of defence; one small break in it is enough for water to reach the cavity.
- A backing wall without a water-resistive layer absorbs the water that entered the cavity and carries it inside.
- If the base of the cavity and the heads of openings have no outlet, water collects behind the facade and finds the next weak point.
- Sills and heads without an outward slope, a drip edge and end dams direct cavity water straight into the opening frame.
- A bracket, horizontal rail or substructure part that acts as a ledge holds water and leads it towards the backing wall and the anchors.
- A parapet coping without a fall towards the roof, or with insufficient overlap, feeds water from the top into the cavity of the entire facade.
Technical proof or diagram
Technical proof state
No metric, project result, or proof image is shown until a verified asset is attached.
The verified diagram should show a vertical section of the facade from the parapet coping to the base of the wall: panel, joint, ventilated cavity, insulation, water-resistive layer on the backing wall, head flashing and sill with end dams, and the water outlet at the base. Water entry routes should be marked with arrows and common failure points with symbols. This technical asset is still pending verification.
- Parapet coping and overlap
- Ventilated cavity and drainage path
- Water-resistive layer on the backing wall
- Head and sill flashing
- Water outlet at the facade base
SIPANEL solution logic
SIPANEL's logic for controlling water penetration in aluminium cladding
Set the water strategy before shop drawings
Before shop drawings are prepared, it is decided whether the facade is face-sealed or a ventilated rainscreen, which layer carries the real waterproofing line, and which contractor builds that layer. Without this decision, each trade assumes another layer will hold the water.
Map interruptions and detail the flashings
Wherever the cavity is interrupted, at opening heads, sills, floor slab lines, corners, the parapet, the base of the facade and services penetrations, it gets its own detail: an outward fall, a drip edge, end dams, and laps arranged so water always lands on the lower layer, never behind it.
Coordinate the backing wall and openings with other trades
Continuity of the water-resistive layer on the backing wall, its connection to window frames and the sealing of bracket anchor holes are coordinated with the masonry and window contractors, and an inspection hold point is set for them before the panels close the wall.
Control the cavity and substructure
The drainage path at the base and above openings is kept open and protected by mesh against insects and debris. Rails and brackets are positioned so water does not sit on them, and separators are provided between dissimilar metals so cavity moisture does not cause corrosion.
Define joints and sealant as the first line
For sealed joints, sealant type, joint width and depth, backer rod and surface preparation are defined according to the panel's thermal movement; but the design ensures that if the sealant weakens over time, water still has a way out.
Diagnose and verify
On a new facade, sample areas are checked with a water spray test before handover. On an existing facade, stain locations are compared with rain direction and timing to separate leaks from condensation; selected panels are then opened and the cause is corrected in the right layer, not just the surface stain.
Technical FAQ
View complete FAQIs it normal for water to get behind aluminium cladding panels?
In a ventilated rainscreen facade, yes; the design accepts that some water passes the joints, runs it down the backing wall and releases it at the base of the facade and above openings. The problem starts when that water has no way out or the backing wall has no water-resistive layer.
If we reseal around the panels, will the leak stop?
Usually not for long. If water enters at the parapet coping, a sill, a bracket anchor hole or a blocked cavity, surface silicone only moves the place where the leak appears. In a rainscreen facade, sealing open joints can even disrupt cavity ventilation and trap moisture behind the panels.
Are open-joint or sealed-joint facades better?
Neither is better on its own. A sealed-joint facade depends on complete continuity and regular maintenance of the sealant. An open-joint facade depends on a water-resistive backing wall, accurate flashings and a drainable cavity. The choice should match the site's wind and rain exposure, the type of backing wall and the possibility of inspection and maintenance.
How can we tell whether an interior stain is a leak or condensation?
A stain that appears during or shortly after rain, on the elevation the wind drove the rain against, points to a leak. A stain that appears on cold nights without rain, on cold surfaces such as frame edges or slab lines and on any elevation, is more likely condensation. Recording the date, orientation and weather each time it appears makes the diagnosis more reliable.
Where should the facade be inspected after heavy rain?
The parapet coping and top edge, the heads and sills of windows, corners, services and signage penetrations, and the base of the facade where water exits. A blocked cavity base, rust around brackets and interior stains aligned with these points should all be recorded.
Can the problem be fixed without removing the whole facade?
In many cases, yes. By comparing where the symptoms appear with the likely water path, a few selected panels are opened to see the cause; the flashing, sill end, coping or backing-wall seal in that area is then corrected. If the backing wall lacks a water-resistive layer across the whole facade, the scope of the repair will be larger.
Related Engineering Resources
Open resource hubRelated Services and Insights
Facade joint control, fixing logic, and material planning.
Aluminium Cladding Joint Control for Industrial FacadesRooflight Dripping in Autumn: Leak or Condensation?Falls through rooflights on industrial roofs in winter workInsights IndexReturn to all engineering insights.
CTA
Review the water path behind your aluminium cladding before the next rains
Send the facade drawings or details, photos of the stains and leak locations and when they appear, and SIPANEL's technical team will review the likely water path, flashings, cavity and backing wall and propose a correction approach.